PSP Error Codes - What They Mean

[WeedZ1985]

There are alot of questions in the help section concerning error codes and what they mean. so i did a little research and will be compiling a list. this is what i've found so far..
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
UKN9000001 - The update data is corrupt and cannot start.
DADADA - DA Firmware update corruption error.
80110305 - memory stick can not be acessed.
80010013 - device / media not found
8001B002 - unknown
80020001 or 800244C - some sort of kernel errors
80020001 - default kernel error (General Error)
800200D9 - failed to allocate the memory block
80020130 - file read error
80020148 - PRX type unsupported
80110482 - occurs when test of wlan infrastructure connection fails
FFFFFED3 - unknown
80410001 or 80410D16 = network errors
80410D07 - unknown
ffffffff - update failed (General Error)
80410A0B - Internal Error
80410410 - Cannot connect to the given acess point
80010087 - The game could not be started =
one of the more common errors. could be a mismatch in required FW. Corrupt or unsupported data
0 - no error go figure :/
80020001 - unknown
80020002 - not implemented
80020032 - illegal exception code
80020033 - exception handler not used
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=

if anyone has anything to add feel free to do so. i'll post more as i find them.

[BCman]

IDSTORAGE key codes...
http://lan.st/showthread.php?t=1430
http://forums.maxconsole.net/showthread.php?t=96911

MOST COMMON ERRORS
80020148 - Unsupported PRX type | This error also seems to appear when you are running an iso with a fake mem.
-Upgrade to a newer custom firmware, or u are using official firmware and u need to downgrade then install CF.
-If not, it is probably a config error/bug and 99% of the time it will be fixed if u "delete flash1 and reset settings" in Recovery>Advanced.
-Often occurs when upgrading from a older OE/SE to M33.
-can also be bad/corrupt iso
-can be from not having 1.5 addon installed when running some homebrew(fat only)
-can be fake memcard.
-also occurs with older SE/OE firmware if u have umd mode set to M33 driver(fixed by changing to sonynp9660 or put in a umd)
-also can be fixed by upgrading to 3.52M33 from older CF.
but most of the time it is a upgrade bug in flash1.
80020321 - Ran a game that doesn't support NO-UMD* (DAX FW ONLY!)
-If u get this error, change iso loader(in recovery or vsh menu) to SONY NP9660 or put a UMD in, ANY umd....but SONY NP9660 iso loader is best.
8002014C - Ran kxploited homebrew without Homebrew enabled firmware.
-enter recovery, enter config, set game kernal to 1.5, exit.(fat psp's only)(make sure u have 1.5 kernal addon installed for the newer 3.xxM33 CF)
-error occurs when noobs try to run 1.5 kernal homebrew with official sony firmware...or a slim(which doesnt support 1.5 kernal either).
-error occurs when running homebrew from wrong folder (eg. put homebrew in GAME371 folder instead of GAME or GAME150 or vice-versa)
8001002 - putting the POPS EBOOT in the wrong folder
-To play ps1 games, take the folder that has the ps1 eboot in it and copy that folder to GAME folder(eg. ms0:\psp\game\Resident Evil\eboot.pbp CF only)
-make sure u have a eboot.bin along with a boot.bin in ur finished product........
-U put the eboot.pbp in wrong folder..............
800200D9 - failed to allocate the memory block
-to fix, disable screenshot PRX or equivilent PRX's....
80010002
-bad rip of game, missing eboot.bin file...
-using a video umd instead of a game umd
-upgrade to newer firmware and use a better iso driver(SONY NP9660 or M33)
80010013
-device / media not found
-bad rip of game, reaccuire a different copy...




SONY PSP NETWORKING ERROR CODES

ERROR CODE
---------------------------------------------------------
80020148 - (unsupported PRX type)?
800201A8 - (WAIT timeout)?
80020130 - File Read Error (ex. length is 0)
80020001 - Generic Kernel Error - default (ex. executable is invalid) 800200D9
- Failure to allocate memory block (ex. missing PSP)
80410D07 - Connection error has occurred. (Ie cant find access pt)
80020001 - error
80020002 - not implemented
80020032 - illegal exception code
80020033 - exception handler not use
80020034 - exception handler already used
80020035 - system call table not use
80020036 - system call table already used
80020037 - illegal system call table
80020038 - illegal Primary Syscall number
80020039 - Primary Syscall number already use
80020064 - call from interrupt handler/thread
80020065 - illegal INTRCODE
80020066 - CPU already interrupt disable
80020067 - Handler already exist
80020068 - Handler not found
80020069 - illegal interrupt level
8002006a - illegal address
8002006b - illegal Intr Handler Option Param size
8002006c - illegal stack address
8002006d - already stack address set
80020096 - not found free Hard Timer
80020097 - illegal timer ID
80020098 - illegal source
80020099 - illegal prescale
8002009a - Hard Timer in use
8002009b - Hard Timer not setup
8002009c - Hard Timer not in use
800200a0 - unit number already used
800200a1 - unit number not used
800200a2 - rom directory not found
800200c8 - id type already exist
800200c9 - id type not exist
800200ca - {not available}
800200cb - unknown UID
800200cc - unmatch UID type
800200cd - id not exist
800200ce - not found UID function
800200cf - UID already holder
x800200d0 - UID not holder
800200d1 - illegal permission
800200d2 - illegal argument
800200d3 - illegal address
800200d4 - the memory area is out of range
800200d5 - the memory area is overlap
800200d6 - illegal partition id
800200d7 - partition in use
800200d8 - illegal memory block allocation type
800200d9 - failed to allocate memory block
800200da - inhibited to resize this memory block
800200db - failed to resize this memory block
800200dc - failed to allocate heap block
800200dd - failed to allocate heap
800200de - illegal chunk id
800200df - cannot find chunk name
800200e0 - there is no free chunk
8002012c - module link error
8002012d - illegal object format (not PRX/PFX)
8002012e - not found Module
8002012f - not found Module file
80020130 - Module file read error
80020131 - memory in use
80020132 - partition mismatch
80020133 - module already started
80020134 - module not started yet
80020135 - module already stopped
80020136 - module cannot stop
80020137 - module not stopped yet
80020138 - module cannot remove
80020139 - exclusive load
8002013a - Library is not linked yet
8002013b - Library already exists
8002013c - Library not found
8002013d - illegal Library header
8002013e - Library isused now
8002013f - module already stopping
80020140 - illegal off set value
80020141 - illegal position code
80020142 - illegal access code
80020143 - module manager busy
80020144 - illegal flag
80020145 - cannot get module list
80020146 - prohibit Load Module device
80020147 - prohibit Load Exec device
80020148 - unsupported PRX type
80020149 - illegal permission call
8002014a - cannot get module information
8002014b - illegal Load Exec buffer
8002014c - illegal Load Exec file name
8002014d - There is no exit callback
80020190 - no memory
80020191 - illegal attr parameter
80020192 - illegal thread entry address
80020193 - illegal priority value
80020194 - illegal stack size
80020195 - illegal mode
80020196 - illegal mask
80020197 - illegal thread ID
80020198 - not found thread
80020199 - not found semaphore
8002019a - not found event flag
8002019b - not found message box
8002019c - not found Vpool
8002019d - not found Fpool
8002019e - not found message pipe
8002019f - not found alarm
800201a0 - not found thread event handler
800201a1 - not found callback
800201a2 - thread already DORMANT
800201a3 - thread already SUSPEND
800201a4 - thread is not DORMANT
800201a5 - thread is not SUSPEND

800201a6 - thread is not WAIT
800201a7 - now dispatch disabled
800201a8 - WAIT timeout
800201a9 - WAIT canceled
800201aa - WAIT status released
N800201ab - WAIT status released with callback
800201ac - thread is terminated
800201ad - semaphore counter zero
800201ae - semaphore counter overflow
800201af - event flag condition not occur
800201b0 - this event flag cannot accept waits with multiple threads
800201b1 - illegal event flag wait pattern
800201b2 - message box have no message
800201b3 - message pipe is full
800201b4 - message pipe is empty
800201b5 - wait object deleted
800201b6 - illegal memory block
800201b7 - illegal memory size
800201b8 - illegal scratchpad address
800201b9 - scratch pad in use
800201ba - scratchpad not in use
800201bb - illegal type
800201bc - illegal size
800201bd - illegal count
800201be - not found vtimer
800201bf - illegal vtimer ID
800201c0 - illegal KTLS ID
800201c1 - KTLS is full
800201c2 - KTLS is busy
80020258 - invalid such priority
80020259 - device name is invalid
8002025a - device name is unknown
8002025b - pm information is registered already
8002025c - pm information is not registered
8002025d - major state is invalid value
8002025e - request is invalid
8002025f - request is unknown
80020260 - unit number is invalid
80020261 - cannot cancel request
80020262 - pm information is invalid
80020263 - argument is invalid
80020264 - already target epower state
80020265 - failed to change system power state
80020266 - cannot change device power state
80020267 - device does not support such power state
800202bc - request to the DMAC failed
800202bd - DMA operation is less or equal one
800202be - the operation is already queued
800202bf - the operation is already finished or not queueud
800202c0 - the operation is already in transfer progress
800202c1 - the operation is not assigned yet
800202c2 - the sync operation timed out
800202c3 - dma operation struct is already freed
800202c4 - dma operation is used
800202c5 - dma operation is empty
800202c6 - DMA operation is aborted
800202c7 - DMA operation is error
800202c8 - physical DMA channel is already reserved
800202c9 - physical DMA channel is not managed by dmac manager
800202ca - there is a privilege address in link list
800202cb - link list buffer is not enough
800202cc - the operation is not assigned to physical DMA channel
800202cd - the operation is child operation
800202ce - it is too much than transferable datasize
800202cf - argument is invalid
80020320 - Too many open files
80020321 - No such device
80020322 - Cross-device link
80020323 - Bad file descriptor
80020324 - Invalid argument
80020325 - Unsupported operation
80020326 - Alias is already used
80020327 - Cannot mount
80020328 - Driver deleted
80020329 - Async operation is busy
8002032a - No async operation
8002032b - Device is already registered
8002032c - No current working directory
8002032d - Filename too long
800203e8 - DECI3 No such device or address
800203e9 - DECI3 I/O error
800203ea - DECI3 Not enough core
800203eb - STDIO not opened
8002044c - Parameter is not cache aligned
8002044d - End of kernel error code Never use this name

[glaukon12]

hey ive got a 80020148 and ive already tried formating flash 1 and it still wont work. now what?

[pspjoke]

Originally Posted by glaukon12

hey ive got a 80020148 and ive already tried formating flash 1 and it still wont work. now what?

80020148 - PRX type unsupported
some more info would be nice..

[glaukon12]

Originally Posted by pspjoke

80020148 - PRX type unsupported
some more info would be nice..

I am trying to run a game boy advance emulator. Ive got 5.00 m33-6 firmware and im using a phat psp. This is my second hacked psp so I know that my memory stick works fine because i can plug it into the other psp and everything loads. For some reason this specific emulator wont work. It just pops up a 80020148 error.

[BCman]

Originally Posted by glaukon12

I am trying to run a game boy advance emulator. Ive got 5.00 m33-6 firmware and im using a phat psp. This is my second hacked psp so I know that my memory stick works fine because i can plug it into the other psp and everything loads. For some reason this specific emulator wont work. It just pops up a 80020148 error.

easy.
install the 1.5 kernal addon and/or set game kernal to 1.5 in recovery menu>config

[chinadangzhj]

thanks for sharing.

[jables666]

dued help!!!!! me i can not copy ebots IOS eoror i have psp cfw 4.01 m33-2 has eoror code 80020148 cant copy eboots and have winRAR so help plea!!!!!!!!!!!!ss

[WeedZ1985]

Wow, thanx BC. you've got alot of common fixes as well

[Xitherun]

sticky this shit.